Daily maintenance and maintenance methods of bottle blowing machine, bottle blowing machine, Machinery Co., Ltd. specializes in producing bottle blowing machine

1. Before turning on the plastic bottle blowing machine in each shift, lubricating oil must be added to each movable part once. (Manipulator, manipulator guide rail, mold opening and closing guide rail) 2. The swing arm can be added once every (3-4) days. The large chain and small chain of the heating machine can be used once a month. Always check whether the reducer of the main engine and the reducer of the heating machine are short of oil. The bearing of the main engine can be added once a month (2-3). 3. Before consumption, check whether the moving parts are strong and whether the screws are loose and scattered, especially whether the center with strong impact force and the belt drive part are abnormal. 4. Check whether the high-pressure gas source, low-pressure gas source, power source, and water source are normal. 5. Check whether each emergency stop switch, safety door switch, maintenance installation detection switch is normal. 6. Check whether the heating head enters the embryo, and the embryo drops are working properly. If the inserts are not in place, you can adjust the mounting nuts for the inserts. 7. Check whether the lamp tube is damaged or broken. It should be replaced in time. 8. Check whether the pneumatic components can leak air and whether the actions are dexterous. 9. Check whether the triplet is leaking abnormally, whether it is blocked, and whether the water cup is too full. 10. 11. When the solenoid valve of the plastic blow molding machine encounters abnormalities, it must be cleaned in time. Plastic blow molding machine molds must be cleaned and polished regularly. 12. When opening the upper and lower pressure air source switches, you must move slowly to prevent the air flow from being too fast and the dirt will blow into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the plastic blow molding machine, you must make sure that the part of the machine is in good condition, that there is no one inside the machine and no foreign matter. Especially the status of the handle, so as not to hurt people. At the same time, close the safety door. 14. When starting the machine, the motor must be started first, and the heating machine must be started after a delay of 30 seconds to prevent the voltage from shaking. Before starting the heating, make sure that the cooling water is turned on. 15. After the heating is started (2-3) minutes, wait until the temperature of the oven rises evenly, and then press the embryo button. At the same time, the blowing must be turned on, otherwise the blowing will not be possible. 16. When the plastic blow molding machine is in operation, it is necessary to pay close attention to whether the machine has any abnormal noise, so as to find out early and stop it in time to solve it early. 17. When there is an emergency, you can press the emergency stop button to press the brake. Then, based on the analysis of the on-site status, the problem was found to be solved quickly. 18. After normal operation, do not extend any part of the body into the machine to avoid the manipulator injuring people. If the machine has abnormal noise, it can be decelerated and then stopped to observe. 19. After normal consumption, the operator must always observe the quality of the bottle, so as not to affect the quality of the bottle blowing due to the shaking of the voltage or other reasons. 20. When repairing, you can press the defect repair button on the touch screen to ensure safe repair. If you need to manually observe the actions of each cavity individually, please pay attention to the status of the robot. At the same time, you must understand the function of the individual button, and then take action. Make sure that mistakes cause unnecessary trouble. twenty one. After each repair, you must clean up tools and screws to avoid leaving them in the machine and affecting the normal operation of the machine.

Yosion Machinery also discusses implications for both research and the practice of operations in building systems to help people succeed in both the short and long run.

You can find a large selection of quality at Yosion Machinery. Go get your desired one.

The bottle making machine bottle blowing machine has significantly numerous benefits over other pet bottle manufacturing machine systems, which makes it first choice for plastic blowing machine manufacturers.