The operating points of the blow molding machine, blow molding machine-professional production of machinery

The operation points of the bottle blowing machine: 1. Before the bottle blowing machine is turned on, it is necessary to add lubricating oil to each movable part once. 2. The swing arm can be added once a day (3-4), and the large chain and small chain of the heating machine can be added once a month. It is necessary to frequently check whether the main reducer and the heating machine reducer are short of oil. The main engine bearing can be added once every 3 months. 3. Before production, check whether the moving parts are strong, whether the screws are loose and falling off, especially whether the transmission part is abnormal in places with strong impact. 4. Check whether the high-pressure gas source, low-pressure gas source, power source, and water source are normal. 5. Check whether each emergency stop switch, safety door switch, and protection device detection switch are normal. 6. Check whether the heating head enters the embryo and the embryo falls is normal. 7. Check if the lamp tube is damaged or cracked. It should be replaced in time. 8. Check whether the pneumatic components are leaking, and whether their movements are sensitive. 9. Check if the triple valve body is leaking abnormally, if it is blocked, and if the water cup is too full. 10. When the solenoid valve of the bottle blowing machine is abnormal, it must be cleaned in time. 11. Blowing molds must be cleaned and cleaned regularly. 12. When turning on the high and low pressure air source switch, you must act slowly to prevent the air flow from being too fast and the dirt will be blown into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the machine, you must make sure that the mechanical parts are in good condition and there is no foreign matter. Especially the movement position to prevent injury. At the same time, close the safety door. 14. When starting the machine, the heating machine must be started first to prevent the voltage from shaking. Before starting the heating, make sure that the cooling water is turned on. 15. After heating up (2-3) minutes, wait until the temperature of the oven rises evenly, and then lower the preform. 16. During the working process of the machine, the blower should pay attention to safety when placing blanks and taking bottles. It is strictly forbidden to reach into the mold. 17. When there is an emergency, you can press the emergency stop button to press the brake. Then analyze the cause of the composition according to the on-site situation, and find out the question and deal with it quickly. 18. When the bottle blowing machine is working, it is necessary to pay close attention to whether there is abnormal noise in the bottle blowing machine, so as to find out early and stop it in time for early treatment. 19. After the bottle blowing machine is working normally, do not extend any part of the body into the machine to prevent the manipulator from hurting people. If the machine has abnormal noise, it must be slowed down for observation. 20. After the bottle blowing machine is in normal production, the operator must always observe the quality of the bottle to prevent the voltage fluctuation or other reasons from affecting the quality of the bottle blowing. 21. When the machine is repaired, you can press the touch screen fault repair button to ensure safe repair. If you need to manually observe the movement of each cavity individually, please pay attention to the orientation of the robotic arm. At the same time, you must understand the effect of the separate button before you act to ensure that the wrong operation causes unnecessary trouble. 22. After each repair of the machine, you must clean up tools and screws to prevent them from being left in the machine, affecting the normal operation of the machine, and avoiding accidents.
Yosion Machinery guarantees to providing quality products and services.
Yosion Machinery’s goal is to provide the customer with an enjoyable, honest service by satisfying individual customers practical transportation needs with a quality product.
To deal with commercial threats, Yosion Machinery konws that the notion of proactively seeking out potential or looming external threats against a company is gaining traction.
A wholesaler should have many bottle making machine based products that could help you if you have a plastic bottle machine problem. It is better to treat the problem early rather than have to deal with it later. Yosion Machinery is your best choice.
Yosion Machinery has developed a unique technology with many applications including pet bottle manufacturing machine.