The importance of the safety of the blow molding machine

Nowadays, safe production has become the consensus of people. No matter how efficient and simple a blow molding machine is, if it loses its safety, it also loses its proper application value. In recent years, safety accidents caused by blow molding machines have occurred frequently. Strengthen production and equipment management, improve the operation level of operators, ensure the safety of production equipment, improve labor productivity, make continuous and stable production, ensure product quality, and reduce production costs. The necessary knowledge of the safety operation specification of the blow molding machine has the following points: 1. Before starting each shift, lubricating oil must be added to each moving part. (Manipulator, manipulator guide rail, mold opening and closing guide rail) 2. The swing arm can be added once every (3-4) days. The large chain and small chain of the heating machine can be used once a month. Always check whether the main engine reducer and the heating machine reducer are short of oil. The main engine bearing can be added once (2-3) months. 3. Before production, check whether the moving parts are firm, whether the screws are loose or falling off, especially in places with strong impact force, and whether the belt transmission part is abnormal. 4. Check whether the high-pressure air source, low-pressure air source, power supply, and water source are normal. 5. Check whether the emergency stop switch, safety door switch, and protection device detection switch are normal. 6. Check whether the heating head enters the embryo and the part that drops the embryo works normally. If the embryo is not in place, the nut of the pressing device can be adjusted. 7. Check whether the lamp tube is damaged or broken. To be replaced in time. 8 . Check whether each pneumatic component is leaking and whether the action is sensitive. 9. Check whether the triplet is abnormally leaking, whether it is blocked, and whether the water storage capacity of the water cup is too full. 10. When the solenoid valve of the blow molding machine is abnormal, it should be cleaned in time (every 3.5 million blows are cleaned). 11. The blow mold must be cleaned and polished regularly. 12. When opening the high and low pressure air source switch, you must move slowly to prevent the air source from blowing too fast and dirt into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the machine, make sure that the mechanical parts are in good condition, there is no one inside the machine, and there is no foreign matter. Especially the crank position, so as not to hurt people. Also close the safety door. 14. When starting the machine, the motor must be started first, and the heating machine must be started with a delay of 30 seconds to prevent voltage fluctuations. Make sure the cooling water is turned on before starting the heating. 15. After heating starts for (2-3) minutes, press the embryo button after the oven temperature rises evenly. At the same time, the blowing bottle should be turned on when it is powered on, otherwise it will not blow the bottle. 16. When the machine is running, it is necessary to pay close attention to whether there is any abnormal noise in the machine, and it is necessary to detect it early and stop it in time to solve it. 17. In case of emergency, you can press the emergency stop button to brake in an emergency. Then analyze the cause of the formation according to the on-site situation, and find the problem and solve it quickly. 18. After the blowing machine is in normal operation, do not put any part of the body into the machine to avoid injury by the manipulator. If the machine has abnormal noise, it can be observed after slowing down. 19. After the machine is in normal production, the operator must always observe the quality of the bottle, so as not to affect the quality of the blowing bottle due to voltage fluctuations or other reasons. 20. When the machine is being repaired, you can press the touch screen fault repair button to ensure safe repair. If you need to manually observe the movement of each cavity individually, pay attention to the position of the robot. At the same time, be sure to understand the role of the individual buttons, and then in the action. Make sure that misoperations cause unnecessary trouble. twenty one. After the machine is repaired, be sure to clean up tools and screws, so as not to leave them in the machine and affect the normal operation of the machine.
Yosion Machinery also discusses implications for both research and the practice of operations in building systems to help people succeed in both the short and long run.
Get blowing machine maker bottle blowing machine from only reliable exporters, go to Yosion Machinery for more details.
Visit Yosion Machinery to find recent dynamics of bottle blowing machine and contact Yosion Machinery for the latest and most capable in global market.
Yosion Machinery knew if this worked for us, it would work for others, so we took the exclusive product and program and re-developed it to be more accessible to customers.