How much do you know about the operation points of the blow molding machine?

1. Before starting each shift, lubricating oil must be added to each moving part. (Manipulator, manipulator guide rail, mold opening and closing guide rail.) 2. The swing arm can be added once (3-4) days, and the large chain and small chain of the heating machine can be added once a month. Always check whether the main reducer and heating reducer are short of oil. The main engine bearing can be added once every 3 months. 3. Before production, check whether the moving parts are firm, whether the screws are loose and fall off, especially whether the transmission parts are abnormal in places with strong impact force. 4. Check whether the high-pressure air source, low-pressure air source, power supply and water source are normal. 5. Check whether the emergency stop switch, safety door switch and protection device detection switch are normal. 6. Check whether the heating head enters the embryo and whether the embryo-dropping part works normally. 7. Check whether the lamp tube is damaged or broken. To be replaced in time. 8. Check whether each pneumatic component is leaking and whether the action is sensitive. 9. Check whether the triple valve body is abnormally leaking, whether it is blocked, and whether the water storage capacity of the water cup is too full. 10. When the solenoid valve of the blow molding machine is abnormal, it should be cleaned in time (every 500,000 blows are cleaned once). 11. The blowing mold must be cleaned and cleaned regularly. 12. When opening the high and low pressure air source switch, it must be moved slowly to prevent the air source from blowing too fast and dirt is blown into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the blow molding machine, make sure that the mechanical part is in good condition and there is no foreign matter. Especially the sports position, so as not to hurt people. Also close the safety door. 14. When starting the machine, the heating machine must be started first to prevent voltage fluctuations. Make sure the cooling water is turned on before starting the heating. 15. Heating start (2—3) After a few minutes, wait for the oven temperature to rise evenly, and then place the preform. 16. During the operation of the machine, the blower should pay attention to safety when placing blanks and taking bottles. It is strictly forbidden to put your hand into the mold. 17. In case of emergency, press the emergency stop button to brake in an emergency. Then analyze the cause of the formation according to the on-site situation, and find the problem and solve it quickly. 18. When the machine is running, it is necessary to pay close attention to whether the machine has abnormal noise. It is necessary to detect it early and stop it in time to solve it. 19. After the machine is running normally, do not put any part of the body into the machine to prevent the manipulator from hurting people. If the machine has abnormal noise, it must be slowed down for observation. 20. After the machine is in normal production, the operator must always observe the quality of the bottle to avoid voltage fluctuation or other reasons affecting the quality of the blowing bottle. 21. When the machine is being repaired, you can press the touch screen fault repair button to ensure safe repair. If you need to manually observe the movement of each cavity individually, pay attention to the position of the robot arm. At the same time, be sure to know the function of the individual buttons before moving them to ensure that misoperations cause unnecessary trouble. 22. After each maintenance of the machine, be sure to clean up tools and screws to avoid leaving them in the machine, affecting the normal operation of the machine and avoiding accidents.
are an important part of the society and they come in handy in any place where there are blwoing machine company in need of yosion bottle blowing machine.
Serving others for customers a better life with bottle blowing machine for employees respect and opportunity.
bottle blowing machine has its grasp on oversees market and has a very good repute. Our products are available at very competitive prices.
Yosion Machinery will need to find one that fits our needs and budgets, and still turns out a quality product.
Knowing what promotions are popular and get the most activity as bottle blowing machine from current and potential customers can play a role in your overall strategy.