loading

YUANYOU Committed to stable performance automatic PET bottle blowing machine production line since 1990s.

Daily blow molding machine operating procedures

1. Before each shift of the fully automatic blow molding machine, lubricating oil must be added to each moving part. (Manipulator, manipulator guide rail, mold opening and closing guide rail) 2. The swing arm can be added once (3-4) days, and the large chain and small chain of the heating machine can be added once a month. Regularly check whether the main engine reducer and heating machine reducer are short of oil, and the main engine bearing can be added once (2-3) months. 3. Before production, check whether the moving parts are firm, whether the screws are loose or falling off, especially in places with strong impact force, and whether the belt transmission part is abnormal. 4. Check whether the high-pressure air source, low-pressure air source, power supply and water source are normal. 5. Check whether the emergency stop switch, safety door switch and protection device detection switch are normal. 6. Check whether the heating head enters the embryo and whether the embryo-dropping part works normally. If the embryo is not in place, the nut of the pressing device can be adjusted. 7. Check whether the lamp tube is damaged or broken. To be replaced in time. 8. Check whether each pneumatic component is leaking and whether the action is sensitive. 9. Check whether the triplet is abnormally leaking, whether it is blocked, and whether the water storage capacity of the water cup is too full. 10. When the solenoid valve of the blow molding machine is abnormal, it should be cleaned in time (every 3.5 million blows are cleaned once). 11. The blowing mold must be cleaned and polished regularly. 12. When opening the high and low pressure air source switch, you must move slowly to prevent the air source from blowing too fast and dirt into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the machine, make sure that the mechanical parts are in good condition, there is no one inside the machine, and there is no foreign matter. Especially the crank position, so as not to hurt people. Also close the safety door. 14. When starting the machine, the motor must be started first, and the heating machine should be started after a delay of 30 seconds to prevent voltage fluctuations. Make sure the cooling water is turned on before starting the heating. 15. After the heating starts (2-3) minutes, wait for the oven temperature to rise evenly, and then press the embryo button. At the same time, the blowing bottle should be turned on when it is powered on, otherwise it will not blow the bottle. 16. When the machine is running, it is necessary to pay close attention to whether the machine has abnormal noise. It is necessary to detect it early and stop it in time to solve it. 17. In case of emergency, press the emergency stop button to brake in an emergency. Then analyze the cause of the formation according to the on-site situation, and find the problem and solve it quickly. 18. After the machine is running normally, do not put any part of the body into the machine to prevent the manipulator from hurting people. If the machine has abnormal noise, it can be observed after slowing down. 19. After the machine is in normal production, the operator must always observe the quality of the bottle to avoid voltage fluctuation or other reasons affecting the quality of the blowing bottle. 20. When the machine is being repaired, you can press the touch screen fault repair button to ensure safe repair. If you need to manually observe the movement of each cavity individually, pay attention to the position of the robot. At the same time, be sure to know the function of the individual buttons before moving them to ensure that misoperations cause unnecessary trouble. 21. After each maintenance of the machine, be sure to clean up tools and screws, so as not to leave them in the machine and affect the normal operation of the machine. The company mainly produces automatic blow molding machines

The global market was valued at pet bottle making machine manufacturers in plastic blowing machine manufacturers and is expected to reach a market value of pet bottle machine price by blwoing machine company, with a CAGR of plastic bottle machine during the forecast period.

Yosion Machinery is one of leading yosion bottle blowing machine bottle blowing machine distributors. You can order , and accessories for your need. Meeting your business need is always our top priority. Any of your enquiry is warmly welcomed.

The same determination is critical for business owners. The journey in bottle blowing machine business is both a challenging and rewarding experience.

GET IN TOUCH WITH Us
recommended articles
Introduction to Injection Molding Machine

Injection molding machine is a manufacturing process for producing parts by injecting molten material into a mold.
From the moment a consumer picks up a bottle of their favorite beverage, to the moment they twist off the cap and take a refreshing sip, the design of PET preforms plays a crucial role in the success of the entire bottling process.
Advanced Software Revolutionizing PET Preform Design

In recent years, advanced software has completely revolutionized the way PET preform design is carried out.
As the demand for bottled beverages continues to rise, so does the environmental impact of the PET bottle blowing industry.
When it comes to the PET bottle blowing industry, there are a myriad of regulatory challenges that companies must navigate in order to remain compliant and successful.
When it comes to producing plastic PET bottles, selecting the right bottle making machine is crucial for achieving high-quality and efficient production.
Advancements in Plastic PET Bottle Making Machines: What’s New?

Plastic PET (Polyethylene Terephthalate) bottles have become a ubiquitous part of our daily lives.
Plastic PET bottle making machines have revolutionized the production process for plastic bottles, making it faster, more efficient, and cost-effective.
Is it Time to Upgrade Your Plastic PET Bottle Making Machine?

When it comes to manufacturing plastic PET bottles, keeping up with the latest technology and equipment is crucial for staying competitive in the market.
PET Injection Machines: Applications and Benefits

Plastic injection molding has become a widely used manufacturing process, especially in the production of PET (polyethylene terephthalate) products.
no data
YUANYOU is striding toward the world with a high-profile attitude, and customers around the world are constantly moving towards Yosion Machinery.
no data
Copyright © 2025 Yosion Machinery  | Sitemap
Customer service
detect