Analyze the operating specifications of the automatic bottle blowing machine, you must check it out if you have a bottle blowing machine
by:Yosion Machinery
2021-05-02
When the automatic bottle blowing machine is repaired, you can press the fault repair button on the touch screen to ensure safe repair. If you need to manually observe the movement of each individual cavity, please pay attention to the position of the manipulator. At the same time, we must be clear about the function of the separate button to ensure that the malfunction causes unnecessary trouble. Operation specification of automatic bottle blowing machine: 1. Lubricating oil must be added to each movable part once before starting each shift. (Manipulator, manipulator guide rail, mold opening and closing guide rail) 2. The swing arm can be added once a day (3-4). The large chain and small chain of the heating machine can be used once a month. Frequently check whether the reducer of the main engine and the reducer of the heating machine are short of oil. The main engine bearing can be added once every 3 months. 3. Before production, check whether the moving parts are firm, whether the ydskyhht screws are loose and falling off, especially whether the belt transmission part is abnormal in places with strong impact. 4. Check whether the high-pressure gas source, low-pressure gas source, power source, and water source are normal. 5. Check whether each emergency stop switch, safety door switch, and protection device detection switch are normal. 6. Check whether the heating head enters the embryo and the embryo falls are working properly. If the embryo insertion is not in place, the nut of the embryo pressing device can be adjusted. 7. Check whether the lamp tube is damaged or broken. It should be replaced in time. 8. Check whether the pneumatic components are leaking and whether their movements are sensitive. 9. Check whether the triplet is leaking abnormally, whether it is blocked, and whether the water cup is too full. 10. When the solenoid valve of the automatic bottle blowing machine encounters an abnormality, it should be cleaned in time (3,500,000 cleaning once per bottle blowing). 11. Blowing molds must be cleaned and polished regularly. 12. When opening the high and low pressure air source switch, you must act slowly to prevent the air flow from being too fast and the dirt will be blown into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the automatic bottle blowing machine, you must make sure that the mechanical parts are in good condition, there is no one inside the machine, and there is no foreign matter. Especially the crank position, so as not to hurt people. At the same time, close the safety door. 14. When starting the machine, the motor must be started first, and the heating machine is started with a delay of 30 seconds to prevent voltage fluctuations. Before starting the heating, ydsky1221 first make sure that the cooling water is turned on. 15. After the heating is started (2-3) minutes, wait until the temperature of the oven rises evenly, and then press the embryo button. At the same time, the blowing must be turned on, otherwise the blowing will not be possible. 16. When the automatic blow molding machine is running, it is necessary to pay close attention to whether the machine has abnormal noise, so as to find out early and stop it in time to solve it early. 17. In an emergency, you can press the emergency stop button to make an emergency brake. Then analyze the causes based on the on-site situation and find the problem to be solved quickly. 18. After the automatic blow molding machine is running normally, do not extend any part of the body into the machine to avoid injury by the manipulator. If the machine has abnormal noise, it can be observed after slowing down. 19. After the normal production of the automatic bottle blowing machine, the operator must always observe the quality of the bottle, so as not to affect the quality of the bottle blowing due to voltage fluctuations or other reasons. 20. When the automatic bottle blowing machine is repaired, you can press the fault repair button on the touch screen to ensure safe repair. If you need to manually observe the movement of each cavity individually, please pay attention to the position of the manipulator. At the same time, we must be clear about the function of the separate button to ensure that the malfunction causes unnecessary trouble. 21. After each maintenance of the automatic blow molding machine, tools and screws must be cleaned to avoid leaving them in the machine and affecting the normal operation of the machine.
These bottle blowing machine blowing machine maker are meant to serve as a guide for business owners on how to both identify potential opportunities for transformative innovation and how to adapt to the constantly changing technologies of today.
You can always ask the experts for the most appropriate pet bottle manufacturing machine bottle blowing machine for your specific needs. Find the best support, prices and other to bottle blowing machine solutions at Yosion Machinery.
It is never too late to have a new mindset and to get things moving in the right direction. Choose Yosion Machinery to be your quality provider.
There are ample scientific evidence of reducing the risk of pet bottle machine price.
These bottle blowing machine blowing machine maker are meant to serve as a guide for business owners on how to both identify potential opportunities for transformative innovation and how to adapt to the constantly changing technologies of today.
You can always ask the experts for the most appropriate pet bottle manufacturing machine bottle blowing machine for your specific needs. Find the best support, prices and other to bottle blowing machine solutions at Yosion Machinery.
It is never too late to have a new mindset and to get things moving in the right direction. Choose Yosion Machinery to be your quality provider.
There are ample scientific evidence of reducing the risk of pet bottle machine price.
Custom message