What are the operating points of the blow molding machine?

Operation points of the blow molding machine: 1. Before starting the blow molding machine, it is necessary to add lubricating oil to each moving part once. 2. The swing arm can be added once (3-4) days, and the large chain and small chain of the heating machine can be added once a month. It is necessary to frequently check whether the main reducer and the heater reducer are short of oil. The main engine bearing can be added once every 3 months. 3. Before production, check whether the moving parts are firm, whether the screws are loose and falling off, especially whether the transmission parts are abnormal in places with strong impact force. 4. Check whether the high-pressure air source, low-pressure air source, power supply, and water source are normal. 5. Check whether the emergency stop switch, safety door switch, and protection device detection switch are normal. 6. Check whether the heating head enters the embryo and the embryo drop part is working normally. 7. Check whether the lamp tube is damaged or cracked. To be replaced in time. 8. Check whether each pneumatic component is leaking and whether the action is sensitive. 9. Check whether the triple valve body is abnormally leaking, whether it is blocked, and whether the water storage capacity of the water cup is too full. 10. When the solenoid valve of the blow molding machine is abnormal, it should be cleaned in time. 11. The blowing mold must be cleaned and cleaned regularly. 12. When opening the high and low pressure air source switch, it must be moved slowly to prevent the air source from blowing too fast and dirt is blown into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the machine, make sure that the mechanical parts are in good condition and there is no foreign matter. Especially in sports position to prevent injury. Also close the safety door. 14. When starting the machine, the heating machine must be started first to prevent the voltage from fluctuating. Make sure the cooling water is turned on before starting the heating. 15. Heating start (2—3) After a few minutes, wait for the oven temperature to rise evenly, and then place the preform. 16. During the working process of the machine, the blower should pay attention to safety when placing blanks and taking bottles. It is strictly forbidden to put your hand into the mold. 17. In case of emergency, you can press the emergency stop button to brake urgently. Then, according to the on-site situation, analyze the reasons for the formation, and find out the problems and deal with them quickly. 18. When the blow molding machine is working, it is necessary to pay close attention to whether the blow molding machine has abnormal noise. It is necessary to detect it early and stop it in time for early treatment. 19. After the blow molding machine is working normally, do not put any part of the body into the machine to prevent the manipulator from hurting people. If the machine has abnormal noise, it must be slowed down for observation. 20. After the normal production of the blowing machine, the operator must always observe the quality of the bottle to prevent the fluctuation of the voltage or other reasons from affecting the quality of the blowing. 21. When the machine is repaired, you can press the touch screen fault repair button to ensure safe repair. If you need to manually observe the movement of each individual cavity, please pay attention to the orientation of the robot arm. At the same time, be sure to understand the effect of a separate button, and then act, to ensure that misoperations lead to unnecessary trouble. 22. After each repair of the machine, be sure to clean up tools and screws to prevent them from being left in the machine, affecting the normal operation of the machine and avoiding accidents.

Everyone who has a yosion bottle blowing machine wants it to look blwoing machine company. However, in order to achieve that, it normally involves investing in a blowing machine maker bottle blowing machine. Yosion Machinery can offer you the best solution.

Finding the best products has been made easier, at Yosion Machinery. Here you can see completed ranges of produced with advanced equipment and strict quality control. Go to Yosion Machinery and send your enquiry if you have any question.

Yosion Machinery, which contributes itself on bottle blowing machine for creating more useful application.

Our company is professional in selling bottle blowing machine as well as providing a series of relevant services.