Daily maintenance and maintenance method of blow molding machine

1. Before opening the plastic blow molding machine in each shift, lubricating oil must be added to each moving part. (manipulator, manipulator guide rail, mold opening and closing guide rail) 2. Swing arm can be (3—4) Add once a day. The large chain and small chain of the heating machine can be used once a month. Always check whether the main engine reducer and the heating machine reducer are short of oil. The main engine bearing can be (2—3) Add once a month. 3. Before production, check whether the moving parts are sturdy, whether the screws are loose, especially the center with strong impact force, and whether the belt drive is abnormal. 4. Check whether the high-pressure air source, low-pressure air source, power supply, and water source are normal. 5. Check whether each emergency stop switch, safety door switch, maintenance and installation detection switch is normal. 6. Check whether the heating head enters the embryo and whether the part of the embryo is removed is normal. If the insert embryo is not in place, the pressure embryo installation nut can be adjusted. 7. Check whether the lamp tube is damaged or broken. To be replaced in time. 8. Check whether each pneumatic component is leaking and whether the action is flexible. 9. Check whether the triplet leaks abnormally, whether it is blocked, and whether the water storage cup is too full. 10. When the solenoid valve of the plastic blow molding machine is abnormal, it should be cleaned in time 11. Plastic blow molding machine molds must be cleaned and polished regularly. 12. When opening the upper and lower pressure air source switch, you must move slowly to prevent the air source from blowing too fast and dirt into the solenoid valve. At the same time, open the exhaust valve for 30 seconds to ensure that the air is clean. 13. When starting the plastic blow molding machine, you must be sure that the mechanical parts are in good condition, there is no one inside the machine, and there is no foreign matter. Especially the handle position, so as not to hurt people. Also close the safety door. 14. When starting the machine, the motor must be started first, and the heating machine must be started with a delay of 30 seconds to prevent the voltage from shaking. Make sure the cooling water is turned on before starting the heating. 15. After heating starts for (2-3) minutes, press the embryo button after the oven temperature rises evenly. At the same time, the blowing bottle should be turned on when it is powered on, otherwise it will not blow the bottle. 16. When the plastic blow molding machine is running, it is necessary to pay close attention to whether the machine has abnormal noise. It is necessary to detect it early and stop it in time to solve it. 17. In case of emergency, you can press the emergency stop button to brake urgently. Then, according to the reasons for the on-site status analysis, find the problem and solve it quickly. 18. After normal operation, do not put any part of the body into the machine to avoid injury by the manipulator. If the machine has abnormal noise, you can stop and observe after slowing down. 19. After normal production, the operator must always observe the quality of the bottle, so as not to shake the voltage or other reasons to affect the quality of the blowing bottle. 20. When repairing, you can press the fault repair button on the touch screen to ensure safe repair. If you need to manually observe the movement of each cavity individually, please pay attention to the position of the robot. At the same time, be sure to understand the function of the independent button, and then act. Make sure that wrong moves cause unnecessary trouble. twenty one. After each repair, be sure to clean up tools and screws, so as not to leave them in the machine and affect the normal operation of the machine.

Whenever you grab your remote and turn on the TV, there are numerous ads promoting bottle blowing machine and offering for plastic blowing machine manufacturers extracts, which are said to boost pet bottle manufacturing machine.

You can count on Yosion Machinery to be your one stop shopping site for most of the quality products you are searching for. We strive to offer a wide variety of products for you to learn about and to purchase. 

By investing in an ethical supply chain, Yosion Machinery position ourselves to engage with a driven, engaged customer base.

Yosion Machinery has enlarged the scope of services, which can fully please customers' demands.